Loading...

Marmorino

SKU: N/A Category:

$63.00$165.00

High-finish lime plaster for interiors, Marmorino allows you to obtain personalized and refined surfaces with slightly marbled effects and a satin sheen.

 

Format ConsumptionCAD $
2.5 kgApprox. 14 ft² (2 coats)63.00
10 kgApprox. 56 ft² (2 coats)165.00
Loading...

Description

 

Marmorino is a high-finish lime plaster for interiors that allows you to obtain personalized and refined surfaces with light marbled effects and a satin sheen. Marmorino is a stucco that is aesthetically similar to Tadelakt plaster. It is perfectly suited to rooms with humid environments thanks to its high alkalinity which makes it antifungal. Packaged as a powder to be diluted with water, it can be tinted with the entire range of Tockay natural dry pigments.

 

Application

 

When using the product, the complete product information must be observed.

TIPSHEET: Surface Preparation for Plasters

TIPSHEET: Protecting Marmorino with Encaustic

 

RECOMMENDED TOOLS

– Venetian trowel (240 x 100 mm)

– Venetian trowel (200 x 80 Mm)

– Steel Trowel (200 x 80 mm)

 

SURFACE CONDITIONS

The surface must be dry, absorbent, coverable, solid, clean, dry, free of grease and any coloring substance that may appear by capillary action.

 

PREPARATION OF THE SUPPORTS

– Remove traces of glue and other chalky or flimsy finishes

– Remove binder build-up from plaster surfaces

– Remove all formwork oil residues from concrete

– Remove crumbly, flimsy plaster or masonry and repair with a similar material

– Carefully brush off powdery substrates

– Clean mouldy substrates with Soda Leach

– Clean mineral substrates affected by mildew with soda lye

 

PREPARATION OF MARMORINO

Pour the powder into the indicated amount of clean, cold water, stir using a powerful mixer (drill with whisk attachment) until a lump-free paste is obtained. Clean the edge of the bucket with a trowel from time to time. Let stand at least 15 minutes, mix again before use.

**Tip: Preparing the mixture one day before application will result in a better consistency (cover with plastic wrap).

 

QUANTITY OF WATER TO USE

1 kg of powder for 350-400 ml of water.

 

TINT

Marmorino can be tinted with up to 10% of Tockay lime-resistant pigments, except for iron oxide pigments, which should not exceed 5%. Mix the pigments with a little water until there are no lumps, then add to the prepared Marmorino. We recommend cleaning the rim of the bucket with a trowel and pouring the tinted plaster into a new, clean bucket to remove any untinted residue on the rim of the bucket. Marmorino pigmented with Ultramarine pigment should be used within 24 hours.

To tint, see our Tockay color chart.

The online color guides are provided for information purposes only. Please note that color tones may not always be displayed correctly by different monitors and their settings. The same applies to prints of these color charts that you make yourself.

 

To get the best impression of our colors, we recommend the purchase of handmade color charts made from casein paint and natural dry pigments.

 

PRIMER

Apply a coat of casein primer to absorbent surfaces such as mineral plaster, gypsum board, cellulose-gypsum board and concrete. Allow to dry completely.

 

LEVELING THE SUBSTRATE

Lime, cement or lime/cement mix plaster substrates do not require an intermediate coat if they are absorbent, untreated and in good condition.

All other plasters, rough surfaces, gypsum plasterboard or cellulose-gypsum boards, must first be covered with a casein primer, then with the 0.9 mm lime plaster.

 

APPLICATION

Minimum application temperature: 8°C. Wet dry surfaces before application.

Marmorino must be applied in 2 coats.

 

1- 1st coat:

Apply Marmorino with a trowel, in a thin coat (about 1 mm, barely thicker than the grain) over the entire surface, uniformly or with a slight structure. Then let it pull until the surface resists pressure. The first coat should not be smoothed to a shine.

 

2- 2nd coat:

Apply a thin, even coat (about 1 mm, barely thicker than the grain) of Marmorino with a trowel. The Marmorino can be compressed with a trowel as soon as it has drawn sufficiently. The right moment to compress depends on the absorption of the support, its residual humidity and the ambient conditions.

 

3- Polishing Soap:

When the surface of the Marmorino resists pressure, apply the Polishing Soap generously over the entire surface, with a soft brush and in an even layer. As soon as the soap has been applied, trowel and carefully remove the excess soap. The result is a strong shine that protects the Marmorino from dirt and water splashes due to the reaction of the soap with the lime that forms a water-repellent lime soaps.

 

4- Alternative:

Instead of applying the second coat of Marmorino until the shine is achieved, it is possible to apply an additional coat of Tockay Decorative Stucco after it has been compressed in a measured manner. This should be squeezed and treated with Polishing Soap as described above.

 

ADDITIONAL TREATMENT

To obtain a higher gloss, apply after at least 24 hours of drying time, Tockay Punic Wax in a thin layer and buff with a Venetian trowel.

 

SPECIAL EFFECTS

For metallic effects, the Punic wax can be tinted with Kreidezeit Pearl Gloss pigments. Other decorative effects can be achieved by using Kreidezeit Multi-Purpose Wax and stencils on the smoothed and soaped surface of the Marmorino. The shade is darker where the wax is applied, for a discreet, velvety decorative effect.

 

DRYING TIME

Dry after approximately 24 hours, at 20°C and 65% humidity.

 

CLEANING OF TOOLS

Clean with water immediately after use.

 

Technical Data

 

Before using this product, consult the Technical Data Sheet.

Safety Data Sheet of the product.

Please note that the yield of Marmorino is given for the 2 coats necessary to achieve this finish. The yield may vary depending on the substrate, the application method and the quality of the surface. Determine exact yield by testing.

 

 

Colour Chart

 

Choose one of the 72 shades in our colour chart and rediscover the forgotten gestures of the craftsman by mixing your own colour using Tockay natural dry pigments!

All natural, non-toxic and free of petroleum-based chemicals, our pigments are packaged in powder form and are easily mixed with water and then incorporated into the paint or plaster according to a precise recipe. For GekkkoSOL silicate-based paints, use GekkkoSOL thinner to dilute the pigments.

– Always be sure to remove lumps

– Ultramarine pigments should be used within 12 hours of preparation when mixed with a lime-based product

 

The online colour guides are provided for information purposes only. Please note that colour tones may not always be displayed correctly by different monitors and their settings. The same applies to prints of these colour charts that you make yourself.

To get the best impression of our colors, we recommend the purchase of handmade colour charts made from casein paint and natural dry pigments.

 

Please consult:

72 colour chart and recipes

10 whites chart and recipes

How to tint your paint or plaster with natural dry pigments

Natural dry pigments