Description

GekkkoSOL is a purely mineral interior wall coating made of silicate. It has a double function. First, it is a finish paint with a smooth texture (matte and slightly velvety) that can be applied directly on an old synthetic paint. It is also an primer, perfect for renovation work because of its exceptional adhesion power. It is particularly useful to make the transition between a synthetic surface and a natural paint such as clay or lime paints. This paint is white, ready to use and can be thinned with GekkkoSOL thinner. It can be tinted with the whole range of Tockay dry pigments.

 

Application

When using the product, the complete product information must be observed.

 

SUITABLE SURFACES

GekkkoSOL smooth paint can be used for various purposes:

– As a primer, prior to the application of Tockay paints

– As a finish paint

– As a primer prior to the application of a stain

 

GekkkoSOL smooth is suitable for interior use on many new surfaces or surfaces to be renovated:

– Old, well-fixed synthetic finishes, especially emulsion paints. Test before applying GekkkoSOL on latex paint!

– Lime plaster, lime/cement, plaster

– Plasterboards and gypsum boards (exception: Rigidur H)

– Old lacquers

– Concrete

On all new lime-based surfaces (plasters and paints), wait at least 4 weeks before painting with GekkkoSOL smooth paint.

 

PREPARATION OF THE SURFACE

The support must be solid, clean, dry, dust-free, degreased, free of any coloring substance likely to appear by capillarity.

– Wash off old glue paints, eliminate chalky or weak paint remains. Remove the remains of wallpaper glue

– Carefully brush off powdery backgrounds

– Remove dust carefully from the surface

– Sand synthetic and lacquered surfaces

– Check the adhesion of old finishes, remove them if necessary

– Remove all residues of formwork oil from the concrete

– Remove crumbly, weak parts and repair them with the same type of material

– Block backgrounds that may show color with Shellac-Shielding primer

– Not suitable for use on wood, chipboard, plywood and related materials

– Clean and treat all traces of mildew on the surface

– All absorbent surfaces (test for absorption), such as plaster or lightly sanded surfaces, should be primed with Waterglass (1:1 dilution with water). Plaster-based plasters and plasters that have been levelled with plaster must be treated with casein primer. Wait approximately 12 hours before starting the next step.

 

DILUTION

**GekkkoSOL smooth should not be diluted with silicates or water. To thin, use only GekkkoSOL thinner.

1- Fine elutriation, on glossy surfaces:

– 1 x GekkkoSOL smooth paint diluted with about 10% GekkkoSOL thinner to adjust the absorption capacity of the surface, if necessary.

 

2- Strong elutriation on dark surfaces:

– 1 x GekkkoSOL smooth paint diluted with about 10% GekkkoSOL thinner to adjust the capacity, if necessary

– 1 x GekkkoSOL smooth paint undiluted or diluted with a maximum of 10% GekkkoSOL thinner

GekkkoSOL smooth paint can be overcoated with any type of Tockay wall paint and stain.

 

APPLICATION

GekkkoSOL smooth should be applied with a brush or a short-haired roller (1.5 cm long). On all highly absorbent surfaces, such as lime-based cement plaster or plaster, a dilution of about 10% of GekkkoSOL thinner is recommended. GekkkoSOL smooth paint is very opaque, so it is important to apply a very thin layer. Too thick layers of paint can cause cracks.

 

TINTING

GekkkoSOL smooth paint can be tinted with a maximum of 10% of natural dry Tockay pigments. The maximum of Iron Oxide pigments is limited to 5%. Stronger shades can be achieved in consultation with Tockay. Before mixing the pigments into the paint, dilute them with GekkkoSOL thinner.

 

DRYING

Fully dry and durable after 28 days. The drying time increases with high humidity and/or low temperature. Sufficient temperate ventilation is essential during drying.

 

CLEANING OF TOOLS

Clean with water immediately after use. If necessary, use Marseille soap.

 

Technical data

It should be noted that the yield may vary depending on the substrate, the application method and the quality of the surface. Determine exact consumption by testing.

Before using this product, consult its Technical Data Sheet available below:

Technical Data Sheet

 

 

Color chart

Choose one of the 72 shades in our color chart and rediscover the forgotten gestures of the craftsman by mixing your own color using Tockay natural dry pigments!

All natural, non-toxic and free of petroleum-based chemicals, our pigments are packaged in powder form and are easily mixed with water and then incorporated into the paint or plaster according to a precise recipe. For GekkkoSOL silicate-based paints, use GekkkoSOL thinner to dilute the pigments.

– Always be sure to remove lumps.

– Only Ultramarine pigments should be used within 12 hours of preparation when mixed with a lime-based product

All color charts available online as well as the paper brochures are orientation guides only. Differences may appear in the representation of colors due to computer screen settings or printing.

To view a more accurate version of our colors, we invite you to make an appointment to visit us in our showroom.

 

Please consult:

72 color chart and recipes

How to tint your paint or coating with dry pigments

Natural dry pigments

 

© Copyright - Distribution Tockay inc. | Proudly created and hosted by Québec Studio